Why do so many people switch to tankless? Mostly three things: hot water that keeps coming, lower standby energy use, and space. A tankless heater stays idle until you open a tap, then fires a high-output burner or electric element to heat water as it flows. With no stored water to keep warm, it wastes less energy between uses, and with regular descaling it can last two decades. It is not magic, though. Performance depends entirely on sizing and installation, which is where our attention goes on every Murray, UT install.
Sizing is where tankless installs succeed or fail. We size by flow rate and temperature rise: add up the fixtures you realistically run at the same time in gallons per minute, then factor in how cold the incoming water gets in winter, since a unit that delivers five gallons per minute at a mild rise may deliver far less when the groundwater is cold. Then comes the infrastructure. A whole-home gas unit can draw 150,000 to 199,000 BTU, which often means a larger gas line or a meter check. Venting must match the unit, and electric tankless models can need a large share of your electrical service, sometimes enough to require a panel upgrade.
Every tankless install from Murray Water Heater includes isolation service valves so future descaling takes minutes instead of hours, a clean gas connection with a sediment trap, correctly pitched and terminated venting, and a pressure relief valve piped to a safe location. If your water is hard, we talk through scale protection, since mineral buildup is what shortens tankless life most. We can add recirculation for faster hot water at distant bathrooms, set the temperature, handle permits where required, and walk you through maintenance before we leave. Call (801) 998-0110 to plan a tankless water heater installation in Murray.
What homeowners call us about most is Water Heater Installation in Murray. Start there if you're not sure what you need.
Signs You Need Tankless Water Heater Installation in Murray
Recognizing the warning signs early can save you money and keep a slow drip from turning into a flooded utility room. Watch for these telltale signs that professional help is needed:
- Preferring a heater that can be repaired and maintained instead of replaced every decade
- Adding a bathroom, soaking tub, or larger shower that needs more hot water
- A home remodel or new build where the gas line and venting can be planned from scratch
- A distant bath or detached space that needs its own hot water source
- Standby losses on a tank that sits idle for long stretches
- A utility area where a bulky tank takes up room you would rather use
- A tank water heater that is ten years old or more and due for replacement
- A tank that cannot keep up with your household's morning routine
Early Action Saves Money
Most water heater failures start small: a popping sound from sediment, a damp spot under the drain valve, or a shower that goes lukewarm a few minutes sooner each week. If you notice any of these signs, contact Murray Water Heater at (801) 998-0110 for a prompt inspection.
Water Heater Trouble? Call Us.
One call gets a technician scheduled and a clear price before any work starts.
Tap to Call (801) 998-0110Your Tankless Water Heater Installation Questions Answered
Why Hire a Professional for Tankless Water Heater Installation?
Buying the right unit is the easy part. The other half is making sure your home can support it. Gas tankless burners can fire at close to 199,000 BTU, so gas line sizing, meter capacity, and pressure under full load all have to check out. Vent materials, lengths, and terminations are dictated by the manufacturer and local code, and condensing units add a condensate drain that should be neutralized. Electric whole-home units can pull more current than an older panel can deliver. Miss one of these, and the unit underperforms or becomes unsafe.
We take the guesswork out of going tankless. That starts with sizing for your busiest hour and coldest water, then making sure the home's gas, vent, and power can support it. We install with service valves for descaling, proper relief valve discharge, and venting built to the manual, then test under real demand before we leave. If a tankless unit is not the best choice for your home, because of cost, supply limits, or how you use hot water, we say so and help you compare other options honestly.
How We Handle Tankless Water Heater Installation
Our workflow is simple and thorough, so nothing gets missed between the fuel supply and the relief line. Here's how we handle tankless water heater installation from start to finish:
Flow Rate & Temperature Rise
We total the fixtures you run at the same time in gallons per minute and factor in winter inlet temperature, so the unit never falls behind in winter.
Supply & Venting Plan
We confirm the gas line and meter can feed the burner's full BTU demand, plan the right venting, and check the panel for electric units before any price is set.
Careful Install
We mount the unit, run gas and venting to the manufacturer's specs, add isolation valves for descaling, and pipe the relief valve and condensate properly.
Test, Set, Explain
Startup includes a full-flow test, a gas pressure check with the burner at high fire, a leak check on every joint, and a plain explanation of settings and maintenance.
Simple Ways to Extend Your Water Heater's Life
A few preventive steps can help you avoid a cold shower or a wet floor down the road. Here are our recommendations:
- Plan on yearly descaling through the service valves, sooner if your water is hard
- Check the vent cap outside for nests, debris, or buildup
- Treating hard water protects the heat exchanger from mineral buildup
- Avoid cranking the temperature higher than you need; about 120F works for most homes
- Keep the inlet screen clear so flow stays strong and the unit fires reliably
- Write down any error codes and call early rather than resetting repeatedly
- Protect outdoor or garage units from freezing, and keep power on during cold snaps so freeze protection works
Comparing DIY and Professional Work
Relighting a pilot by following the label is one thing. Diagnosing a gas valve, a burned-out element, a dirty flame sensor, or a tankless error code calls for meters and know-how that a pro brings. Here's how the two approaches stack up:
| Consideration | DIY Attempt | Professional Service |
|---|---|---|
| Capacity | Chosen by brand or price alone | Sized by GPM and winter temperature rise |
| Gas Supply | No check of meter or pressure | Gas pressure tested at high fire |
| Venting | Exhaust risk from improper venting | Condensing or stainless venting done properly |
| Power Needs | Overloaded circuits and tripped breakers | Panel and circuits confirmed before install |
| Maintenance Access | Hard water left unaddressed | Scale protection discussed up front |
| Result | Lukewarm water and error codes | Safe, inspected, and working as designed |
Book a Visit Today
The sooner you call, the sooner the hot water is back. Reach Murray Water Heater for fast service.
Call (801) 998-0110 NowCommunities We Cover
Our service area reaches well past the city limits. Choose your community for local details.